These cookies are necessary for the basic functions of the shop.
"Allow all cookies" cookie
"Decline all cookies" cookie
These cookies are used to make the shopping experience even more appealing, for example for the recognition of the visitor.
Statistics & Tracking
Track device being used
Fault indicator for overhead line
Item number: IKI-Overhead_R2
Item number: IKI-Overhead_R2
With the IKI-Overhead R2, overhead lines can be easily monitored for faults and thus integrated... more
Product information "IKI-Overhead R2"
With the IKI-Overhead R2, overhead lines can be easily monitored for faults and thus integrated into the overall protection concept to minimize downtime. Fault indication is provided locally via strong LEDs and optionally via remote transmission to a central control station.
Fault detection of all typical overhead line faultsShort circuits, transients and ground faults
Ultra-bright LED displayVisibility cone 360° , visible even in bright sunlight
Easy installation using actuating rodIntegrated torque indicator shows correct installation. No additional tools required.
Reliable fault detectiondue to independent current/time characteristic [UMZ); short and earth [short] circuit detection; high impedance fault detection by dI/dT detection; inrush suppression; fault confirmation by monitoring for disconnection via integrated voltage sensor
Simple parameter setting by DIP switchResponse current (automatic or fixed thresholds 200 - 600 A). Reset time (2 - 8 h, manual or automatic after load current recovery). Access to DIP switches possible without tools.
Long lifedue to high quality lithium battery, nanowatt technology and corrosion-free housing.
Easy installationTorque indicator for safe mounting
IKI-Overhead R2 with remote signalling: Radio and Butler versionsAll communication elements are directly installed in the overhead line indicators. Therefore, no additional telecontrol unit mounted on the pole is required.
Easy connection to the control center via IEC 60870-5-104With the optionally available SMS gateway, all installed IKI overhead R2 are connected to the control center or the PONLINE system and integrated
Detection of conductor breakage in the overhead lineDetection of conductor breakage without fault current
Transmission of load current valuesInstantaneous or average values are transmitted cyclically
Remote parameterization of settings possible
Communication principleUp to 8 IKI overhead radios communicate with one IKI overhead butler via short-range radio. The IKI overhead butler communicates via GSM with the PONLINE master server or any SMS receivers. The PONLINE master server can be connected to the control room via an IEC 60870-5-104 interface.
Principle of fault detection with remote signallingFaults are detected and reported right up to the fault location in each case
Display of all relevant status informationIn conjunction with PONLINE®, all important information (faults and load flow) from the overhead line network, such as all types of faults and load flow information, is recorded and transmitted.
|Product designation||IKI-Overhead R2 Fault indicator for overhead line|
|Display Visibility||Approx. 50-100 m in bright sunlight |
approx. 500 m at night
|Display flashing frequency||30 per minute|
|Brightness display||13 Candela|
|Dimensions and installation instructions|
|Case height x width x depth||250 x 104 x 145 mm|
|Conductor cross section||20 - 490 mm²; 5 - 35 mm diameter|
|Operating temperature||-30°C ... 75°C|
|Storage temperature||-30°C ... 80°C|
|Voltage level||Applicable up to 36 kV|
|Maximum height operation||4500 m above sea level|
|Maximum wind force||70 m/s|
|Short circuit detection I>>||✓|
|Threshold current short-circuit detection I>> [A]||200, 400, 600|
|Automatic response threshold Short circuit detection||✓|
|Threshold time short-circuit detection I>> [ms]||80, 150|
|Threshold time short-circuit detection (I>>) adjustable via DIP [ms]||80, 150|
|Waiting time after current switch-off (short-circuit detection) [ms]||200|
|Earth short-circuit detection Ie>>||✓|
|Reset setting||2, 4, 8 h|
|Reset||Time, manually by actuating rod, automatically after load current return > 3 A|
|SIM card format||Standard-SIM (Mini-SIM)|
|Battery life||Approx. 15 years|
|Battery total display time||2BBD Stunden (120 Tage)|