Adapter Sx auf PI
Adapter switch, 1F to 2F, 0.2 m
Adapterweiche, 1F auf 2F, 0.4 m
Adapterweiche, 1F auf 2F, 1.5 m
To connect the Small-Signal Sensor-Adapter to IKI-55; 0.25 m
To connect the Small-Signal Sensor-Adapter to IKI-55; 1.5 m
To connect CAPDIS and IKI-LUM to IKI-55
To Connect CAPDIS, voltage sensors and IKI-LUM to IKI-55
Cutout for one device
Cutout for two devices
Bus connection between three IKIs, 3 x 60 cm, incl. termination resistor
Bus connection between two IKIs, 2 x 60 cm, incl. termination resistor
Directional Split-Core Transducer for C-Cone Bushing
Directional Split-Core Transducer for SIEMENS-Bushing
CT for bushings, 1% deviation, directional, for measured value acquisition, for C-cone, set
CT for bushings, 1% deviation, directional, for measurement, for C-cone, set
CT for bushings, 1% deviation, directional, for measured value acquisition, for Siemens switchgears, set
CT for bushings, directional, for measured value acquisition, for C-cone, set
CT for bushings, directional, for measured value acquisition, for Siemens switchgears, set
For hotsticks with bayonet connector
For direct connection to capacitive sensor (IKI-23 with LRM-Module)
For IKIs with bayonet connector
For IKIs with ring eyelet
for split-core CT, set 3 x 3 m
for split-core CT, set 3 x 3 m, in braided sleeving
for split-core CT, set 3 x 5 m
for split-core CT, set, length on request
for summation transformers, 1 x 5 m
Device in housing, IP66, for CAPDIS-Sx
Device in housing, IP66, for IKI
IKI to CAPDIS-PI-RR4, screened, 0.3 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 0.5 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 1.5 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 1.5 m, 2 x system connector, decoupled
IKI to CAPDIS-PI-RR4, screened, 10 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 10 m, 2 x system connector, decoupled
IKI to CAPDIS-PI-RR4, screened, 3 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 3 m, 2 x system connector, decoupled
IKI to CAPDIS-PI-RR4, screened, 6 m, 2 x system connector
IKI to CAPDIS-PI-RR4, screened, 6 m, 2 x system connector, decoupled
IKI to CAPDIS, shielded, 0.25 m, 2 x system connector, decoupled
IKI to CAPDIS, shielded, 0.4 m, 2 x Sx blade plug to system connector
IKI to CAPDIS, shielded, 0.4 m, 2 x Sx blade plug to system connector, decoupled
IKI to CAPDIS, shielded, 0.4 m, 2 x system connector
IKI to CAPDIS, shielded, 0.4 m, 2 x system connector, 2x 90° tilted
IKI to CAPDIS, shielded, 0.4 m, 2 x system connector, decoupled
IKI to CAPDIS, 0.4 m, Sx blade plug to system plug
IKI to CAPDIS, 0.4 m, Sx blade plug to system plug, decoupled
IKI to CAPDIS, shielded, 1.5 m, 2 x Sx blade plug to system connector
IKI to CAPDIS, shielded, 1.5 m, 2 x Sx blade plug to system connector, decoupled
IKI to CAPDIS, shielded, 1.5 m, 2 x system connector
IKI to CAPDIS, shielded, 1.5 m, 2 x system connector , decoupled
IKI to CAPDIS, 1.5 m, Sx blade plug to system plug
IKI to CAPDIS, 1.5 m, Sx blade plug to system plug, decoupled
IKI to CAPDIS, shielded, 10 m, 2 x Sx blade plug to system connector
IKI to CAPDIS, shielded, 10 m, 2 x Sx blade plug to system connector, decoupled
IKI to CAPDIS, 2 m, Sx blade plug to system plug
IKI to CAPDIS, shielded, 3 m, 2 x Sx blade plug to system connector
IKI to CAPDIS, shielded, 3 m, 2 x Sx blade plug to system connector, decoupled
IKI to CAPDIS, shielded, 3 m, 2 x system connector
IKI to CAPDIS, shielded, 3 m, 2 x system connector , decoupled
IKI to CAPDIS, 3 m, Sx blade plug to system plug
IKI to CAPDIS, shielded, 6 m, 2 x Sx blade plug to system connector
IKI to CAPDIS, shielded, 6 m, 2 x Sx blade plug to system connector, decoupled
IKI to CAPDIS, shielded, 6 m, 2 x system connector
IKI-50 to OAS, 0.4 m, Sx flat plug to system plug, double flat plug sleeve
IKI system connector to wire end sleeves
Directional Split-Core Transducer
Split-core CT, directional, for data acquisition, with cable tie, set
Configuration software for IKI series
Length and connectors on request
Split-core CT, directional, set
Split-core CT, directional, for measured value acquisition, for unshielded ground cable terminations, set
Split-core CT, directional, for measured value acquisition, for unshielded ground cable terminations, Set of 3
Split-core CT, non-directional, for IKI-30, for C-cone bushings, for Siemens switchgears, set
Split-core CT, non-directional, for IKI-30, for C-cone bushings, set
Split-core CT, non-directional, for IKI-30, set
Mini-USB to USB
Primary Tester for Fault Indicators of IKI-Line
Series of split-core and bushing CTs, directional
Series of split-core and bushing CTs, directional, for measurement value acquisition
Series of split-core and bushing CTs, directional, for measurement value acquisition, high precision
Balanced core CT 60 x 314 mm
Balanced core CT, D = 130 mm
Balanced core CT, D = 160 mm
Extension for y-cables, 3 m, wire end sleeves
Extension for y-cables, 0.3 m
Extension for y-cables, 0.6 m
Extension for y-cables, 1.5 m
Extension for y-cables, 3 m
Extension for y-cables, 4.5 m
To connect ohmic voltage sensors to IKIs
IKI-LUM_30_d92 
IKI-LUM_30_d92 
Modbus connection cable 
Modbus connection cable 
IKI-LUM-ISO_IP66 
