IKI-50_1F R2e

IKI-50_1F R2e

Universal fault indicator for intelligent distribution substations

Item number: 2502461
The universal fault indicator IKI-50 R2e is the appropriate solution for intelligent... more
Product information "IKI-50_1F R2e"
The universal fault indicator IKI-50 R2e is the appropriate solution for intelligent distribution substations and offers distribution system operators a high level of transparency and cost-effectiveness. The IKI-50 R2e includes all algorithms for selective fault detection. It is suitable for all neutral point treatments. Information on faults, load curves or limit violations is thus available on site as well as in the central network control center. Faults can be detected and localized immediately.

The IKI-50_1F R2e monitors one feeder.

Fault detection

  • Directional short-circuit detection
  • Directional ground short-circuit detection, directional static ground fault detection (wattmetric method), directional transient ground fault detection (wiper method), earth fault detection via pulse locating
  • Suitable for all neutral point treatments
  • No summing transformer required

Fault early detection

  • Fault early detection by detection of transient disturbances
  • Partial discharge trend detection together with CAPDIS-S2_55 (R5)

Load flow measurement

  • Voltages, Currents, powers, frequencies, cos-phi, . ."
  • Momentary and average values
  • Limit monitoring

Network automation

  • Extensive logic functions freely programmable with PC software KriesConfig

IKI-50 R2e is maintenance-free

  • No battery
  • Unlimited data retention
  • Fault indication in case of power failure over 6 hours
.

Comparison of products

IKI-50_1F R2e
2502461
IKI-50_1F R2
2502352
Level of digitalisation12
Directional short-circuit detection I>>
Directional earth short-circuit detection Ie>>
Earth fault transient detection
Pulsation detection
Directional static earth fault detection Ie>;
Slave test
Relay outputs46
Modbus-RTU
Modbus-RTU Slave
CT-supplied--
Auxiliary power supply24...230 VAC/DC (jeweils  15 %)24...230 VAC/DC (jeweils  15 %)
Buffer of power supplyCapacitor (6h)Capacitor (6h)
USB interfaceMini-USBMini-USB
Digital Inputs46
Digital Outputs44
Digital IOs configurableYesYes
Switching functions feeder control unit--Switching of up to two load switches
1.5-pole switching
Digital outputs for 1.5 pole switching2
Voltage inputs1 (LRM/CAPDIS)2 (1x LRM/CAPDIS, 1x precision 3.25V)
Voltage measurement
Precision voltage measurementYes
Measuring range voltageCapacitive (Input F1), Precision divider with an output signal of 3.25 V/sqrt(3) in nominal operation (input UF2)
Cross calibration-
Current measurement
Logic functions programmableA total of 32 logic rules can be programmed.A total of 32 logic rules can be programmed.
Balanced core CT optional--
Stromwandlerliste für VergleichstabelleIKI-LUM_d92 Split-Core Transducer with cable tie (set) | Ø 92mm (2512106_H001)
IKI-LUM_d92 Split-Core Transducer for C-Cone-Bushings (set) | Ø 92mm (2512106_H003)
IKI-LUM_d92 Split-Core Transducer for SIEMENS-Bushings (set) | Ø 92mm (2512106_H004)
IKI-LUM_d92 Split-Core Transducer with cable tie (set) | Ø 92mm (2512106_H001)
IKI-LUM_d92 Split-Core Transducer for C-Cone-Bushings (set) | Ø 92mm (2512106_H003)
IKI-LUM_d92 Split-Core Transducer for SIEMENS-Bushings (set) | Ø 92mm (2512106_H004)
TE trend monitoring
  • in connection with CAPDIS-S2_55 (R5)
  • Indication on display, transmission via Modbus-RTU
  • Partial discharge trend via frequency distribution; integration over 24h, trend over 72h
  • in conjunction with CAPDIS-S2_55 (R5)
  • Indication on the display, transmission via Modbus-RTU
  • Partial discharge trend via frequency distribution; integration over 24h, trend over 72h
Device data
Article number2502461
Product designationIKI-50_1F R2e Universal fault indicator for intelligent distribution substations
Operating elements and display
Front displayLC-Display and LEDs
Direction keysOperation via four direction keys
Red LED (1)Error event detected | internal energy storage empty
Yellow LED (2)Slave test | Primary test | Device warnings
Dreen LED (3)Status message device status
Two feeder monitoring-
Buffer of power supplyCapacitor (6h)
Dimensions and installation instructions
Case height x width x depth49 x 96 x 108 mm
Cutout height x width45 x 92 mm
Norm cutout dimensionsDIN IEC 61554:2002-08
Installation typePanel mounting
Sheet thickness1.5 ... 2.5 mm
Operating conditions
Operating temperature-25°C ... 55°C
Storage temperature-25°C ... 70°C
Humiditymax. 95 % relative Feuchte bei 40° C
Protection classIP54 (Front)
Fault detection and failure forecast
Fault detectionIndividually selectable, any combinations possible
Star point typesShort-term low-ohmic terminated neutral, Low-ohmic terminated neutral, Inductive terminated neutral, Isolated neutral
Short circuit detection I>>
Directional short-circuit detection I>>
Threshold current short-circuit detection I>>100 A ... 1,000 A (adjustable in steps)
Threshold time short-circuit detection I>>40 ms ... 1,600 ms (adjustable in steps)
Earth short-circuit detection Ie>>
Directional earth short-circuit detection Ie>>
Threshold current earth short-circuit detection Ie>>40 A ... 1,000 A (adjustable in steps)
Threshold time earth short-circuit detection Ie>>40 ms ... 1,600 ms (adjustable in steps)
Directional static earth fault detection Ie>;
Threshold current static earth fault detection Ie>2 A ... 30 A (adjustable in steps)
Directional transient earth fault detection Ie>
Threshold current transient earth fault detection 3I01 A ... 1,000 A (freely adjustable)
Threshold voltage transient earth fault detection 3U01 kV ... 300 kV (freely adjustable)
Earth fault detection via pulse locating
Pulse length of pulse locatingsymmetrical / asymmetrical
Transient fault detection IIe>
TE trend monitoring
  • in connection with CAPDIS-S2_55 (R5)
  • Indication on display, transmission via Modbus-RTU
  • Partial discharge trend via frequency distribution; integration over 24h, trend over 72h
Fault resetAuto, Manually on the device, After time (1 h ... 8 h, configurable)
Event logThe last 20 fault events are stored with event number, date, time, name of the triggering fault detection, fault direction, phase and fault current value.
Earth fault transient detection
Directional earth short-circuit detection
Interfaces and communication
USB interfaceMini-USB
Modbus-RTU
Modbus-RTU Slave
Modbus transmission rates [kBd]9600, 19200, 38400, 57600, 115200
Slave test
Digital Inputs4
Potential-free digital inputs4
Digital Outputs4
Digital IOs configurableYes
Switching functions feeder control unit--
Connection cable cross sectionMax. 2,5 mm
Switching capacity relayAC: max. 62,5 VA max. 2A; max. 250 VAC
DC: max. 2A @ 40 VDC
Relay outputs4
Voltage inputs1 (LRM/CAPDIS)
Current transformer3
Measurement values and functions
Voltage measurement
Phase-to-ground voltages
Phase to phase voltages
Measuring range voltage0.02 kV ... 92 kV | Start of voltage measuring range: 2% of Un
Cross calibration-
Current measurement
Measuring range current0.5 A ... 1,158 A (with current transformer IKI-LUM)
Zero-sequence current
Conductor currents
Active power
Reactive power
Apparent power
Rotary field detection
Frequency measurement
Mean value determination
Min-max value determination
Phase position
Phase shift cos-phi
Limit value monitoringVoltage, current, frequency, reactive power and voltage
Logic functions programmableA total of 32 logic rules can be programmed.
Power supply
Auxiliary power supply24...230 VAC/DC (jeweils  15 %)
Power consumption2 W
Insulation voltage2 kV, 1 min
CT-supplied-
Capacitor buffer
Display buffer for fault indicationUnlimited data retention (independent of auxiliary power and buffer power);
Error display after power failure (depending on adjustable follow-up time):
  • with overrun time 12 seconds: 6 hours
  • with run-on time 60 seconds: 4.5 hours